893103 PRO SYSTEMPart # 6753901 Revision:10/27/971ASSEMBLY INSTRUCTIONS
1001234561/2 1/2 1/2 1/2 1/2 1/2 FIGURE 12• LOOSELY assemble two 3-1/2” PULLEYS (23) and two CABLE RETAINING CLIPS (56) to the CENTER PULLEYBRACK
• SECURELY assemble the BEARING HOUSING (13) and the CENTER PULLEY BRACKET (16) to the UPRIGHT FRAME (1)using two 1/2 X 3-1/4” BOLTS (26) and two 1/
• Assemble the LEFT (15) & RIGHT (14) PEC ARMS to the BEARING HOUSING (13) using four 3/4” FLANGE BEARING(41) and two 3/4” CAP NUTS (52) as show
893103 CABLE DIAGRAM• Refer to the 839103 CABLE DIAGRAM for help with STEPS 17-27LAT CABLE &LOW ROW CABLE25PEC DEC CABLE2424252513
143/8 X 2” 29• Place one 3-1/2” PULLEY (23) into the loop ofthe CABLE (25) below the first and secondPULLEY of the TOP BOOM (2) as shown inFIGURE 1
FIGURE 20• SECURELY assemble one 3-1/2” PULLEY (23) and one CABLE RETAINING CLIP (56) to the plate on the UPRIGHTFRAME (1) using one 3/8 X 2” BOLT (
STEP 22• Wrap the PEC DEC CABLE (24) around one 3-1/2” PULLEY(23) and assemble the PULLEY to the PULLEY BRACKET(11) using one 3/8 X 2” BOLT (29) and
17 FIGURE 24• Route the CABLE (25) under the 3-1/2” PULLEY in the slot on the FRONT UPRIGHT (1) and around the 3-1/2” PULLEY shownon FIGURE 24.
18 FIGURE 25STEP 25:• Loop the CABLE (25) around one 3-1/2” PULLEY (23) and LOOSELY assemble PULLEY to the 1-3/4 X 5-1/4” PLATES(17) using one 3
FIGURE 26STEP 26:• Route CABLE (25) around PULLEY and under the CABLE RETAINING CLIP on FRONT UPRIGHT (1) as shown in FIGURE26.• Attach the CA
IMPORTANT NOTESPlease note:Tools Required for Assembly* Thank you for purchasing the Parabody 893103 PRO SYSTEM. Please read these instructions thor
FIGURE 27STEP 27:• Attach the LOW ROW BAR (18)to the CABLE (25) using two 5/16” SNAP LINKS (37) and one CHAIN (39) as shown inFIGURE 27.• Att
3PARTS LIST3PART #656660365667026546302656690365670026581102656980265673026567502656780365165026568102656830365686036568703657040365424026274402659740
4• Assemble two COVER CAPS (48) to the ends of the BENT TUBE (4) as shown in FIGURE 2.FIGURE 2STEP 2:• SECURELY assemble the LOW ROW ATTACHMENT (1
5• LOOSELY assemble the UPRIGHTS (5) to the BENT TUBE (4) using four 3/8 X 2-3/4” BOLTS (28) and four 3/8” LOCK-NUTS (36) as shown in FIGURE 3.FIGU
6FIGURE 4STEP 4:• Attach ten 1-1/2 X 3/4” GLIDES (54) to both SAFETY RAILS (9) as shown in FIGURE 4.• SECURELY assemble one SPRING PIN ASSEMBLY (4
7• Pull back the SPRING PIN and slide the SAFETY RAILS (9) over the UPRIGHTS (5) until the SPRING PIN is engaged in thefirst hole.FIGURE 6STEP 6: 1
8FIGURE 8STEP 8:01234561/2 1/2 1/2 1/2 1/2 1/227 1/2 X 3”28 3/8 X 2-3/4” 23236 134301/2 X 3” 27 5• LOOSELY assemble the TOP BOOM (2) to the UPRIGH
9FIGURE 111/2 X 3-1/4” 26• SECURELY assemble the SPRING PIN ASSEMBLY (40) to the SWIVEL KNEE SUPPORT (10) as shown in FIGURE 11.STEP 11:• SECUREL
Kommentare zu diesen Handbüchern