1881 LEG PRESS ADAPTER KITFOR 880 GYM SYSTEMCLASS HPART # 7168701REV. CVersion: 881102Revision: 3/08/02USER’S GUIDEWARNING:Read and follow all directi
STEP 8: FIGURE 8• Remove the 3-1/2” PULLEY, one 3/8 X 3-3/4” BOLT, two 3/8 X 1” SPACERS and one 3/8” LOCK NUT from the BASE PLATES asshown in FI
11STEP 10: FIGURE 10• SECURELY assemble the LEG PRESS ADAPTER (1) to the BASE FRAME using one 3/8 X 3-3/4” BOLT (9), one previouslyremoved 3/8 X
12 FIGURE 12STEP 12:• Carefully route the SHORT LEG PRESS CABLE (2) around one 3-1/2” PULLEY (4) and SECURELY assemble the 3-1/2” PULLEY(4) to the
13 FIGURE 14STEP 14:• Carefully route the LEG PRESS CABLE (2) around one 3-1/2” PULLEY (4) and SECURELY assemble the 3-1/2” PULLEY (4) tothe brack
FIGURE 15STEP15:• Carefully route the SHORT LEG PRESS CABLE (2) around one 3-1/2” PULLEY (4) and SECURELY assemble the 3-1/2”PULLEY (4) to the S
FIGURE 18STEP 18:• Carefully route the SHORT LEG PRESS CABLE (2) around one 3-1/2” PULLEY (4) and SECURELY assemble the 3-1/2” PULLEY(4) to the M
FIGURE 19STEP 19:3/8 X 4-1/2” 10 21213 SEAT FRAME1416• SECURELY assemble the threaded end of the SHORT LEG PRESS CABLE (2) to the SEAT FRAME usi
FIGURE 20STEP 20:• To set the correct amount of tension in the cables, push the HEAD PLATE down, insert the WEIGHT SELECTOR PIN and performsever
STEP 1:01234561/2 1/2 1/2 1/2 1/2 1/2• If the SECOND STACK OPTION has not been assembled to the 880, refer to the SECOND STACK OPTION USER’SGUIDE.
STEP 2: FIGURE 219• Route the LONG LEG PRESS CABLE (3) around the 3-1/2” PULLEY on the PULLEY PLATES using one existing 3/8 X 1-3/4”BOLT and one
THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OFEQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES!1. Before using, read all the warnings and
20STEP 3: FIGURE 3• Remove the two 3/8” BOLTS, 3/8” WASHERS and 3/8” LOCK NUTS from the STACK BASE as shown in FIGURE 3.STACK BASE• SECURELY as
2101234561/2 1/2 1/2 1/2 1/2 1/2 FIGURE 5STEP 5:• Carefully route the LONG LEG PRESS CABLE (3) around one 3-1/2” PULLEY (4) and SECURELY assemble
22 FIGURE 7STEP 7:• Carefully route the LONG LEG PRESS CABLE (3) around one 3-1/2” PULLEY (4) and SECURELY assemble the 3-1/2” PULLEY(4) to the br
FIGURE 8STEP 8:• Carefully route the LONG LEG PRESS CABLE (3) around one 3-1/2” PULLEY (4) and SECURELY assemble the 3-1/2” PULLEY(4) to the SEA
FIGURE 11STEP 11:• Carefully route the LONG LEG PRESS CABLE (3) around one 3-1/2” PULLEY (4) and SECURELY assemble the 3-1/2” PULLEY(4) to the MA
FIGURE 12STEP 12:3/8 X 4-1/2” 10 31213 SEAT FRAME1425• SECURELY assemble the threaded end of the LONG LEG PRESS CABLE (3) to the SEAT FRAME usin
26STEP 13:• To set the correct amount of tension in the cables, push the HEAD PLATE down, insert the WEIGHT SELECTOR PIN and performseveral repititi
IMPORTANT NOTESPlease note:Tools Required for Assembly* Thank you for purchasing the ParaBody 881 LEG PRESS ADAPTER KIT. Please read these instruct
PARTS LIST4PART #7160008715600171561023116201310250131028023102924310292231029053102935KEY12345678910QTY1119784235PART #653350131028076122701648030172
STEP 1: FIGURE 101234561/2 1/2 1/2 1/2 1/2 1/2• REMOVE the LAT CABLE, THREADED HOUSING, 3/8 X 3-3/4” BOLT, two 3/8 X 1” SPACERS and one 3/8” LOCK
6STEP 2: FIGURE 2• Remove the PEC STATION PAD from the FRAME, then discard the two 3/8 X 2-3/4” BOLTS. See FIGURE 2.3/8 X 2-3/4”STEP 3: FIGUR
STEP 4: FIGURE 47• Remove the two 3/8 X 4” BOLTS, four 3/8” WASHERS and two 3/8” LOCK NUTS from the REAR UPRIGHT as shown inFIGURE 4. Discard the
STEP 6: FIGURE 6• Route the SHORT LEG CABLE (2) through the FRAME and BOOM BRACKET as shown in FIGURE 4. (NOTE: Removepulleys for ease of install
STEP 7: FIGURE 7• Route the SHORT LEG PRESS CABLE (2) through the PULLEY PLATES as shown in FIGURE 7.3/8 X 1-3/4” 7• Route the SHORT LEG PR
Kommentare zu diesen Handbüchern