1835 HIP SLED SYSTEMCLASS HPART # 7339501REV. BRevision: 12/09/02USER’S GUIDEWARNING:Read and follow all directionsfor each step to insure properassem
FIGURE 6STEP 6:1001234561/2 1/2 1/2 1/2 1/2 1/2• Insert four 2” SQ. END CAPS (26) into the each end of the CARRIAGE (16) as shown in FIGURE 6.• SE
FIGURE 7STEP 7:11• SECURELY assemble two 2” DIA. WHEELS (21) to the BRACKETS on the left side of the CARRIAGE (16) as shown inFIGURE 7 using two 3/8
FIGURE 8STEP 8:01234561/2 1/2 1/2 1/2 1/2 1/212• Remove the two temporary 1/2 X 4-1/2” BOLTS (43) from STEP 5.• Swing the LEFT (8) and RIGHT (9) R
FIGURE 913• SECURELY reassemble the LEFT (8) and RIGHT (9) RAILS to the REAR UPRIGHT (6) as shown in FIGURE 9 using the two 1/2X 4-1/2” BOLTS (43),
STEP 10:1401234561/2 1/2 1/2 1/2 1/2 1/2• SECURELY assemble both WEIGHT SUPPORT (13) and PAD SUPPORTS 93)to the CARRIAGE (16) as shown in FIGURE 10
FIGURE 11STEP 11:15• SECURELY assemble the two PAD SUPPORTS (3) to the CARRIAGE (16) as shown in FIGURE 11 using two 1/2 X 3-1/4”BOLTS (41), four 1
FIGURE 12STEP 12:1601234561/2 1/2 1/2 1/2 1/2 1/2• Attach two 1-1/4” SQ. RUBBER BUMPERS (24) to the ends of the ANGLES of the FOOT PLATE (10) as sho
FIGURE 13STEP 13:17• Assemble the FOOT PLATE (10) to the CARRIAGE (16) as shown in FIGURE 13, using two 1/2 X 1-1/4” BOLTS (39), two 1/2”WASHERS (32
FIGURE 14STEP 14:18• To assemble the CARRIAGE STOP BAR (7) to the side of the LEFT RAIL (8), start by inserting the top of the BAR (7) into theBUSHI
FIGURE 1519STEP 15:• SECURELY assemble the PAD STOP (15) to the BACK PAD (19) as shown in FIGURE 15 using two 3/8 X 1” BOLTS (35), two3/8” LOCK WASH
THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OFEQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES!1. Before using, read all the warnings and
STEP 16:2001234561/2 1/2 1/2 1/2 1/2 1/2FIGURE 16• The PLATFORM (11) can adjust into three positions: 35, 40, and 45 degrees• The HIP SLED was de
FIGURE 17STEP 17:21• To perform LEG PRESSES, center the BACK PAD (19) down on top of the PLATFORM (11) and lock the PAD STOP (15) on theback of the
MAINTENANCEMODEL #________________________SERIAL #_________________________DATE OF PURCHASE: _____________DEALERS NAME: _________________DEALERS PHONE
23NOTES:LIMITED WARRANTYParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN
INTERNATIONAL OFFICESLife FitnessAtlantic BVAtlantic HeadquartersBijdorpplein 25-312992 LB BarendrechtThe NetherlandsPhone: (180) 646 666Fax: (180) 6
IMPORTANT NOTESPlease note:Tools Required for Assembly* Thank you for purchasing the ParaBody 835 Hip Sled System. Please read these instructions t
1 Square = 1’ X 1’41’7’6’5’4’3’2’8’1’ 2’3’ 4’ 5’9’
5PARTS LISTPART #LEA6504909LEA6506809LEA7337609LEA6507709LEA6507809LEA6667809LEA6505910LEA7337309LEA7337409LEA6504410LEA7337710LEA6506610LEA6507010LEA
FIGURE 1STEP 1:• LOOSELY assemble the RIGHT (4) and LEFT HANDLES (5) to the BASE (1) on their respective sides using four 3/8 X 3” BOLTS (37),eight
FIGURE 2STEP 2:7• Insert four 1/2” FLANGE BEARINGS (46) into the BUSHINGS on the BASE (1), and four 1/2” FLANGE BEARINGS (46) intothe BUSHINGS on t
STEP 4:801234561/2 1/2 1/2 1/2 1/2 1/2• Assemble the PLATFORM SLEEVE (2) to the BASE (1) as shown in FIGURE 4 using one 1/2 X 4” BOLT (42), and one
FIGURE 5STEP 5:9• LOOSELY assemble the LEFT (8) and RIGHT RAILS (9), along with the SEAT PAD (18) to the BASE (1) as shown in FIGURE 5using two 3/8
Kommentare zu diesen Handbüchern